Home :: MITSUBISHI / EAGLE :: DSM: 1g (1990-94) :: Brakes :: Brake Upgrades :: Ford Cobra Front Big Brake Upgrade :: Brake Upgrade Kits :: Ford Cobra Front Big Brake Upgrade Kit: 1g DSM

Ford Cobra Front Big Brake Upgrade Kit: 1g DSM

Ford Cobra Front Big Brake Upgrade Kit: 1g DSM
 
(0 reviews)  

Build your custom Cobra caliper, rotor & hardware kit!

This kit starts with our own mounting bracket and hardware kit, including the hubcentric rings you need to properly mount the 13" (330mm) Ford Cobra rotors to your DSM. You can then add the calipers, pads, rotors, and brake lines of your choice. It should be noted that the Ford Cobra calipers use a banjo fitting as the attachement point for the brake lines which is NOT compatible with the stock 1g DSM brake lines.

The rebuilt Ford Cobra calipers are available in 4 finishes: bare cast, painted gloss red, painted gloss black, or painted flat black. There is NO core charge associated with these calipers. If calipers are purchased with this kit, a new banjo bolt and sealing crush washers will be included with each caliper.  For details on the Cobra calipers, please refer to the "Related products" section near the bottom of the page.

It should be noted that the rebuilt calipers that we offer in painted finish are NOT powder coated or painted at the factory. We purchase the calipers in a bare cast state and spray paint them to order. We mask areas such as bleeder screw ports, brake line ports, bolts and the like from overspray, but the calipers are NOT completely disassembled into individual components, painted, then reassembled. The results are similar to what one would expect if they painted the calipers themselves. We are, afterall, charging only $35 to paint two calipers. It should also be noted that we paint these calipers only when an order is placed, we do NOT stock pre-painted calipers and since it takes a full day for painted calipers to dry, any order that includes them will be shipped out one day later than it would have otherwise.

NOTE: Photo is for display purposes and depicts a full kit with EBC USR slotted rotors.  Be assured that your order will correspond to your selections in the drop-down.

NOTE: For details of the various available calipers, rotors, pads, and lines, please refer to the "Related products" link near the bottom of the page.

NOTE: A set hubcentric rings is comprised of four rings (two pairs of different sizes). For details, please refer to the "Related products" link near the bottom of the page.

NOTE: If lines for all four corners are ordered, rear lines will be for stock 1g DSM rear calipers.

NOTE: These brakes will NOT fit with all 17" & 18" wheels (and essentially no 16"ers)--the area of interference is rarely the inner diameter of the rim, but rather, the inner surface of the rim "spokes". Since the design of this area can vary widely from rim to rim, (and is not easily measured) it's virtually impossible for RTM Racing to confirm fitment. It should be noted, however, that most interference issues of this type can be remedied with wheel spaces to further offset the rim to the outboard side. We carry wheel spacers--for details please refer to the "Related products" link near the bottom of the page. There are some rims we know WILL fit, there are some we know WON'T. We MAY have knowledge of your particular rims--contact RTM Racing for details.

THE MORE YOU BUY, THE MORE YOU SAVE!  Purchase either a pair of calipers or a pair of premium rotors as part of your kit, and we will reduce the price of the bracket/hardware kit by $30.00.  Purchase both, and we will lower the price by $60.00.  Add a set of premium pads (Hawk or EBC) and brake lines, and we will reduce the price by $90.00!  You will be getting the brackets and hardware at well below our cost!

Application: DSM (1990-94).

Build your custom kit from drop-downs below:

SKU 1K-RTM-Cobra-Cobra-BrakeKit1g
{{step.name}} Qty:

Please complete all selections in the kit to see the final price

There have been no reviews